Arduino/esp8266/micropython/ports/stm32/boards/STM32F7DISC/mpconfigboard.h

#define MICROPY_HW_BOARD_NAME       "F7DISC"
#define MICROPY_HW_MCU_NAME         "STM32F746"

#define MICROPY_HW_HAS_SWITCH       (1)
#define MICROPY_HW_HAS_FLASH        (1)
#define MICROPY_HW_HAS_SDCARD       (1)
#define MICROPY_HW_ENABLE_RNG       (1)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_USB       (1)

#define MICROPY_BOARD_EARLY_INIT    STM32F7DISC_board_early_init
void STM32F7DISC_board_early_init(void);

// HSE is 25MHz
// VCOClock = HSE * PLLN / PLLM = 25 MHz * 432 / 25 = 432 MHz
// SYSCLK = VCOClock / PLLP = 432 MHz / 2 = 216 MHz
// USB/SDMMC/RNG Clock = VCOClock / PLLQ = 432 MHz / 9 = 48 MHz
#define MICROPY_HW_CLK_PLLM (25)
#define MICROPY_HW_CLK_PLLN (432)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (9)

// From the reference manual, for 2.7V to 3.6V
// 151-180 MHz => 5 wait states
// 181-210 MHz => 6 wait states
// 211-216 MHz => 7 wait states
#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_7 // 210-216 MHz needs 7 wait states

// UART config
#define MICROPY_HW_UART1_TX         (pin_A9)
#define MICROPY_HW_UART1_RX         (pin_B7)
#define MICROPY_HW_UART6_TX         (pin_C6)
#define MICROPY_HW_UART6_RX         (pin_C7)
#define MICROPY_HW_UART7_TX         (pin_F6)
#define MICROPY_HW_UART7_RX         (pin_F7)
#define MICROPY_HW_UART_REPL        PYB_UART_1
#define MICROPY_HW_UART_REPL_BAUD   115200

// I2C busses
#define MICROPY_HW_I2C1_SCL         (pin_B8)
#define MICROPY_HW_I2C1_SDA         (pin_B9)

#define MICROPY_HW_I2C3_SCL         (pin_H7)
#define MICROPY_HW_I2C3_SDA         (pin_H8)

// SPI
#define MICROPY_HW_SPI2_NSS         (pin_I0)
#define MICROPY_HW_SPI2_SCK         (pin_I1)
#define MICROPY_HW_SPI2_MISO        (pin_B14)
#define MICROPY_HW_SPI2_MOSI        (pin_B15)

// CAN busses
#define MICROPY_HW_CAN1_TX          (pin_B9)
#define MICROPY_HW_CAN1_RX          (pin_B8)
#define MICROPY_HW_CAN2_TX          (pin_B13)
#define MICROPY_HW_CAN2_RX          (pin_B12)

// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN        (pin_I11)
#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED    (1)

// LEDs
#define MICROPY_HW_LED1             (pin_I1) // green
#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))

// SD card detect switch
#define MICROPY_HW_SDCARD_DETECT_PIN        (pin_C13)
#define MICROPY_HW_SDCARD_DETECT_PULL       (GPIO_PULLUP)
#define MICROPY_HW_SDCARD_DETECT_PRESENT    (GPIO_PIN_RESET)

// USB config (CN13 - USB OTG FS)
// The Hardware VBUS detect only works on pin PA9. The STM32F7 Discovery uses
// PA9 for VCP_TX functionality and connects the VBUS to pin J12 (so software
// only detect). So we don't define the VBUS detect pin since that requires PA9.
#define MICROPY_HW_USB_FS              (1)
/*#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_J12)*/
#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)